日韩欧国产精品一区综合无码,亚洲人成无码www久久久,国产成人无码精品一区不卡

新聞中心

聯系我們更多>>

深圳市百千成電子有限公司
地址:深圳市光明新區長圳社區長鳳路343號
電話:86-0755-26788241
傳真:86-0755-26788245

公司新聞新聞中心 > 公司新聞 > PCB Quality Control

PCB Quality Control

點擊數:1 發布日期:2017/8/3

Virtually every electronic product is constructed with one or more printed-circuit boards (PCBs). The PCBs hold the ICs and other components and implement the interconnections between them. PCBs are created in abundance for portable electronics, computers, and entertainment equipment. They are also made for test equipment, manufacturing, and spacecraft. And for PCB manufacturing, PCB quality check is highly important. PCBs are often produced in bulk, so any kind of fault that would hamper the effective operation of one PCB could affect dozens or even hundreds of them.

And also will hinder very much to the following processes such as PCB assembly process.

To control PCB quality need to operate one step by one. Following are some experiences for PCB quality check of our company.

DRC Check

The Design Rules Check (DRC) is the first also most important step in PCB quality control. If this step can’t be well controlled then the following steps will be hard to move on. When we receive a new order from a customer, we will use an automated tool to verify that the layout does not have any specific placement, routing or other addressable layout errors.

This DRC check will check the netlist and layout against the PCB design constraints and rules. It checks the board’s component placement and trace routing integrity for overlapping components, untraced pins, incorrect layer placement and constraints that are set for trace width routing and clearances. We also do the manufacturing rule check to make sure the PCB design is manufacturable. If we find any errors we will get in contact with the customer, or if we find the PCB design is not manufacturable we’ll provide some suggestions to customer, to do some changes on their design thus to match with our production capacity.

Electrical Testing

Electrical Testing is the second step for PCB quality control, also a key step. For prototype orders and production orders we have different methods.

Prototype Orders:

We offer Flying-Probe E-Test which means your circuit board (PCB) is checked through a device called a Flying-Probe E-Tester. The Flying probe testers we use have few restrictions on access, require no test fixtures, and can test boards with virtually unlimited number of nets. The Tester will check for short circuits, open circuits and make sure the nets of the PCB we made is the same as the nets in your design. After testing is complete, the fail rate of your boards will be less than 1%. Flying-Probe E-Test can save e-test fixture cost for you, while its testing time takes long so we only employ it in prototype orders.

Bulk Orders

We use Testing fixtures to test PCB quality for bulk orders. The fixture contains an array of small, spring-loaded pogo pins; each pogo pin makes contact with one node in the circuitry of the DUT (device under test). By pressing the DUT down against the bed of nails, reliable contact can be quickly and simultaneously made with numerous of individual test points within the circuitry of the DUT.

The Tester will check for short circuits, open circuits, and make sure the nets of the PCB we made is the same as the nets in your design. After testing is complete, the fail rate of PCBs will be less than 0.1%. It is effective and more accurate, and in bulk order we’ll do 100% fixture e-test for you.

AOI ( Automated optical inspection )

We use an AOI to check the inner layers of multi-layers PCB. AOI visually scans the surface of the PCB. The board is lit by several light sources and observed by a scanner or by a number of high definition cameras. This enables the monitoring of all areas of the board.

This inspection is much more reliable and repeatable than manual visual inspection.

The last step for PCB quality check of each order is a 100% visual inspection. Each part is checked for workmanship, quality, cleanliness and a number of other attributes before the boards are packaged for shipping. We’ll always try to provide our “ABP” service and quality for you!

久久亚洲精品无码观看不卡,Aⅴ精品无码无卡在线观看,无码精品国产一区二区免费,亚洲av无码乱码在线观看

PCB Quality Control

在線銷售

技術支持

售后服務